Replacement Parts

NOTE: This is a pack of 12 individual Universal Pop Bottle Waterers. They work on old fashioned snap on pop bottles and they snap on 12 or 16 ounce bottles. Waterers fits through 1'' square opening in cage or pen to supply adequate water for birds or small animals. Waterer supplied with spring to hold bottle. Please note: purchase does NOT include a bottle.

Replacement heater unit for Little Giant 9300 incubator. Still air- No fan.

The IncuStatTM lets you add a sophisticated control module to your cabinet (or larger-style) egg incubator. This is designed to control the temperature, air circulation, and automatic turner motors in your incubator. Key features- Proportional thermostat - minimizes temperature swings (see details below)- Comes pre-set to 99.5 degrees F (easily adjustable, if desired)- Electronically controlled - Digital display- Controls the heater, fan and egg turner motors (it is not required to use this module to control all accessories, if you desire not to)- Hatch timer- Thermostat is calibration enabled- 110/120v power input- Remote sensor for accurate temperature reading- Easily mounts into your incubator (see video below)- Maximum heater wattage: 300 watts (see note below if you need more power) NOTE: if your incubator needs more power than 300 watts, you have the option of using a heater that is always on in order to bump up the entire wattage inside the incubator. For example, if you think you will need about 350 watts for your incubator, you can put a 60 watt light bulb inside the incubator that is always on. Then when the heater that you are regulating with the thermostat is on, you will have enough power in your incubator. Feel free to contact us if you would like further clarifications about this option. See this video to see how easy it is to install the Incubator Control Module: What is the difference between a proportional thermostat and an on/off thermostat? An off/off style thermostat turns the heater on full power when the temperature gets too low. Then it turns it completely off when the temperature gets too high. This style creates a wider swing in temperature because the temperature has to get too high or low before the thermostat responds. The proportional style thermostat adjusts the power up and down as the temperature starts getting close to the set-point (your target temperature). It will reduce the amount of power going to the heater as the temperature gets close to the set-point. Then it will increase the power as the temperature starts falling away from the set-point. This allows the temperature swing to be much smaller than the on/off style thermostat. When incubating eggs, accuracy counts! That is why a proportional style thermostat is preferred. Product Instructions: IncuStat™ Advanced

This listing is for brand new 250 watt replacement heater coil and insulator kit for cabinet style incubators. 250 watts of power Voltage requirement: 110/120VAC Click here to see the 220V International Version. Replaces the standard 250 watt coil heater kit in cabinet style incubators

Replacement wafer for Hova-Bator and GQF egg incubators and brooders. Wafer ONLY. This is not a complete thermostat.

Brand new 100 watt heater. Great for mid-sized incubators. 100 watts of power Voltage requirement: 110/120VAC Standard pink female connectors will fit on the electrical ends of this heater (see video) Would you like to see how easy it is to wire this? See this short video:

The Plug ‘n Play Hygrostat is a digital electronic hygrostat with remote sensor designed specifically to control the humidity level in incubators and terrariums. It's great for both tabletop and cabinet incubators and large and small terrariums.  It comes pre-wired and ready to use. You can use watering device up to 500 Watts and you can use up to three devices. Simply plug in your pump, water valve, humidifier or any other watering device into the 3-outlet plug and you’re ready to go. The humidity set point can be adjusted in 1% increments. Setting it is very simple to do.  This unit comes with a 40 inch remote sensor that can be placed inside your incubator.  It also has a remote temperature sensor so it can compensate humidity measurements for changes in temperature.  Please note: this device does not display the temperature.   Set point can be adjusted to any humidity level between 1% - 99% Runs on 110V AC and will power 110V AC devices.  If you have a DC watering device, you'll need a power converter to change AC to DC (like a laptop power supply).   Calibration enabled. This means that you can calibrate the hygrostat, if required. For example, if you have a hygrometer that you trust and the digital hygrostat reads a little different, you can calibrate the hygrotstat to match the trusted hygrometer (calibrate in 1% increments up to +/- 10%) You are able to change the hysteresis from 1% - 30%.  This means you are able to set the range of humidity that turns the power on and off.  For example, if you set a hysteresis of 5, the hygrostat will wait until the humidity level has dropped 5% below your set point before turning on the power.  It will turn off the power as soon as the level hits the set point This device can also be set to control the power for a dehumidifying device as well, if desired (only one at a time, it can't do both at a time).   You will notice in the pictures that there are two different sensor probes.  The larger one senses the moisture level.  The smaller one measures temperature so that the humidity sensor can compensate for changes in temperature. As noted above, this unit does not display temperature.   What devices can I use with this device to get water into my container?   Great question!  There are three main options to consider. 1. Water valve - use a small water valve attached to a reservoir of water that is kept above your container.  When the valve is powered on, the valve opens and water flows into your chamber. The water can fill a water reservoir in your container of flow onto a wicking pad.  2. Small water pump - A mini pump will bring water from a container kept outside the container.  This is set up similar to the water valve but the water container does not have to be kept above your container.  3. Humidifier - you can get a mini unit that could fit insider your container or a larger one that would be kept outside the container and then use flexible pipe or hose to pump the moist air into your container.  With egg incubators, be sure to find one that have low enough air flow that it will not cool off the incubator too much.   Note: It is normal for the hygrostat to turn the watering device off and still have the humidity level increase a little bit. This happens because as the power to the watering device turns off, the water that has already entered the container still needs to warm up and stabilize. The same is true when the power turns back on: the humidity may decrease a little more as the water takes time to dissipate in your container.  The amount this happens will depend on how quickly your watering device puts water (or mist) into your container.   Keep in mind that the variation in humidity levels over a short period of time is not nearly as important as the average humidity level over several days.   As always, all of our products are covered by our One-year Hassle-free Guarantee. Purchase today with no worries and experience the Plug ‘n Hygrostat for yourself. Product Instructions: Plug N' Play Hygorstat

Universal Pop bottle Waterers work on old fashioned snap on pop bottles and they snap on 12 or 16 ounce bottles. Waterers fits through 1'' square opening in cage or pen to supply adequate water for birds or small animals. Waterer supplied with spring to hold bottle. Please note: purchase does NOT include a bottle.

IncuStat Advanced for IncuKit XL. This device lets you add a sophisticated control module to your cabinet (or larger-style) egg incubator. This is designed to control the temperature, air circulation and automatic turner motors in your incubator. Key features- Proportional thermostat - minimizes temperature swings (see details below)- Comes pre-set to 99.5 degrees F (easily adjustable, if desired)- Electronically controlled - Digital display- Controls the heater, fan and egg turner motors (it is not required to use this module to control all accessories, if you desire not to)- Hatch timer- Thermostat is calibration enabled- 110/120v power input - Remote sensor for accurate temperature reading- Easily mounts into your incubator (see video below)- Maximum heater wattage: 300 watts (see note below if you need more power) NOTE: if your incubator needs more power than 300 watts, you have the option of using a heater that is always on in order to bump up the entire wattage inside the incubator. For example, if you think you will need about 350 watts for your incubator, you can put a 60-watt light bulb inside the incubator that is always on. Then when the heater that you are regulating with the thermostat is on, you will have enough power in your incubator. Feel free to contact us if you would like further clarification about this option. See this video to see how easy it is to install the Incubator Control Module:   What is the difference between a proportional thermostat and an on/off thermostat? An off/off style thermostat turns the heater on full power when the temperature gets too low. Then it turns it completely off when the temperature gets too high. This style creates a wider swing in temperature because the temperature has to get too high or low before the thermostat responds. The proportional style thermostat adjusts the power up and down as the temperature starts getting close to the set-point (your target temperature). It will reduce the amount of power going to the heater as the temperature gets close to the set-point. Then it will increase the power as the temperature starts falling away from the set-point. This allows the temperature swing to be much less than the on/off style thermostat. When incubating eggs, accuracy counts! That is why a proportional-style thermostat is preferred.

The Plug ‘n Play is a digital electronic thermostat with remote sensor designed specifically for incubators. It's great for both tabletop and cabinet incubators. It comes pre-wired and ready to use. You can use any heating element up to 225 Watts. Simply plug in your heater, heat mat, or light bulb to the 3 outlet plug outlet and you’re ready to go. The temperature can be adjusted in 0.1 degree increments. Just press the up or down arrow to set it. The screen has a flame icon that turns on when the heater is operating. This unit comes with a 24 inch remote sensor that can be placed inside your incubator. The white thermostat may be mounted on the outside of the incubator. Comes preset to 99.5 degrees F (37.5 in Celsius mode). Set point can be adjusted to any temperature between 41-113 degrees F If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc. The digital readout displays temperature to the tenth of a degree (98.7, 99.4) The temperature switching differential is 0.2 degrees F. This means that if the temperature is set to 99.5 then the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7 110V AC Calibration enabled. This means that you can calibrate the thermostat if required. For example, if you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds) Note: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the amount of heat your heating element holds and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the eggs to heat or cool more than it should. As long as the up and down cycle is relatively small, less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. As always, all of our products are covered by our 2 Year IncuCare Warranty. Purchase today with no worries and experience the Plug ‘n Play Digital Electronic Thermostat for yourself.

AutoCoop Door Controller with timer makes it so you can set the time when your coop door will open and close. The easy to set digital timer allows you to set when your coop door will open and close down to the minute. The AutoCoop Door Controller is also easy and simple to install. Works with safe 12v power. Power supply not included.

Frame for Hova-Bator turner only. Racks and motor not included.

Power Supply for AutoCoop Door Kits

Blue light indicates when electricity is on. When power outage occurs the alarm will sound after ten seconds and the red light will come on. The alarm will continue to sound until reset is pressed or power returns. If you have chicks or birds that need looking after when electricity goes off on a cold windy night, plug in this unit in your bedroom to wake you when the electricity goes off.   

This is a specialized plug for the GQF 1588 Genesis incubator.  It has been designed to work with the wiring in this incubator, which is different than the normal 12V car plugs on the market. This allows you to plug your incubator into the 12V plug in your car and operate your incubator as normal.  Please note: if your incubator has an egg turner, it will not be powered by this plug.   

AutoCoop Linear Actuator

Replacement Sensor for HumidiKit

Replacement Bottom for IncuView Incubator

Adjusting screw and wing nut for GQF wafer thermostats.

Turning Tray for IncuView Incubator

Two replacement bulbs for the GQF No. 9046 COOL-LITE Egg Tester.

Replacement turner motor assembly for cabinet model incubators featuring the 3258 digital command center. 110 VAC NOTE: If the incubator has a single fan and a 3258 command center, use the original galvanized brackets with the new motor.