Search results for "heat":

  Incubator Warehouse's Digital Electronic Egg Incubator Thermostat for IncuKit XL Description: This thermostat is very simple to use. Just press the up arrow to set the temperature (in 0.1 degree increments). There is a flame indicator on the screen that shows when the heater is operating. The unit has an 18 inch remote sensor that is placed inside the incubator. The white thermostat case is then mounted on the outside of the incubator. Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) 110V AC Power Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7. NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should. As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. Calibration Enabled. This means that you can calibrate the thermostat to a specific temperature. For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds).  

15.9 g Poultry electrolyte supplement with trace minerals to help maintain proper electrolyte balance. Concentrated formula to be dissolved in poultry drinking water Intended to replenish electrolytes lost due to heat Can help chickens stay hydrated and healthy Contains vitamins, minerals and electrolytes A blend of vitamins and minerals designed to support flock health and help restore electrolyte levels in poultry following stress from heat, illness and other environmental changes. Heat stress is especially serious for chickens because of the difficulty in regulating their own body temperature. Excessive heat can put chickens at risk for an electrolyte imbalance due to mineral loss. These minerals may not always be replenished through their diet, which is why supplementation is so important to maintain a healthy and normal electrolyte balance. Sodium is critical for normal nerve and muscle function as well as transport of many substances, such as glucose, across cell membranes. Magnesium serves as an electrolyte in the blood, as an activator of hundreds of enzymes, and as a participant in muscle contractions. Calcium has important roles in muscle contraction, blood clotting, enzyme regulation and hormone release.

Putting a fan inside your incubator is a great way to increase hatch rates, but it is not just as simple as buying a PC fan or a cheap fan kit. There are a few things that you need to keep in mind: Too much air circulation is BAD for eggs (it will dry them out). Think about it, in nature there isn't a fan blowing on eggs. The only reason that an incubator needs the fan is to keep the temperature more consistent (like in nature). BEWARE of CHEAP kits. They often use regular HIGH speed fans. Almost all the fans on the market are designed to move as much air as possible. This is not what you want. If you get too powerful of a fan it can OVERHEAT your incubator. Fans generate heat. Many people have come to check on their eggs only to find them cooked because the fan caused the incubator to overheat. The direction the air flows and the positioning of the fan inside your incubator is critical to maintaining a consistent temperature throughout the incubator. Highlights of the Incubator Warehouse Circulated Air Fan Kit for the Little Giant 9300 Tested & proven for the Little Giant Incubator to increase hatch rates Specially designed to move only as much air as necessary to keep the incubator temperature consistent Will not overheat your incubator!!! Full color installation instructions for an easy installation Backed by the Incubator Warehouse TWO YEAR HASSLE FREE GUARANTEE Did you know that at any given time the temperature in your Little Giant still air incubator can vary by up to 5 degrees from the top and bottom and from the center to the corners? In addition, you get variation from the thermostat cycling the heating unit on and off. This temperature variation has a significant impact on your hatch rates. This problem can be significantly reduced by installing a circulated air fan kit into you incubator. Heat naturally rises, so you need to circulate the hot air from the hot spots to the cool spots for a much more uniform and consistent temperature and better hatch results. The more consistent air temperature also ensures that your thermostat is cycling on and off at the appropriate times, not just when the air around the thermostat heats or cools. Installation Video: 9300 Fan Installation Guide

For incubators and brooders. Indicates when heat is on. 110 volt. Fits 1/2'' hole.  Direct Replacement for HovaBator 1602N

This dimmer switch works perfectly with Wonder Watt heat tape. This allows you to control the amount of power that goes into Wonder Watt and as a result, controls the temperature. Total length of the cord is 5 feet. Works for 110 Volt (100 watts MAX) & 220/240V (200 Watts MAX) PowerWonder Watt is a great way to heat many applications. Some examples include: Egg incubatorsReptile cagesReptile warm spotsDog housesPipesSeed germination mats Plant startsSatellite discsDesk warmerKeyboard warmerFoot warmer ...and just about anything else you can think of that you would want to warm up. This dimmer switch allows you to regulate how much power goes to the Wonder Watt heat tape so you can increase or decrease the temperataue. It can also help ensure you don't overheat the tape. Very simple to use, just plug the cord from your heat tape into the dimmer plug and then the dimmer plug into the wall. That's it! The knob turns to let you regulate how much power goes in.Let us know if you have any questions.Wondering how to configure Wonder Watt? Please see these three instructional videos. The dimmer in this listing replaces the turn-style dimmer in these videos. After you attach it to your Flex Watt, it requires NO additional wiring, just plug it in! Video #1: Shows how to attach the clips insulators. Video #2: Shows how to splice in the dimmer. Video #3: Shows how to mount Flex Watt using foil tape.

This innovative design conforms to the surface to better transfer heat to your bucket. This combined with the insulating pad ensures that the warmth get more effectivley to the water which allows this lower power heater to still be effective down to 0 degrees F. Keeps upto 3 gallons of water from freezing down to 0°F! Need more than 3 gallons? Try 96 watt designed for 5-gallon Provides better freeze protection with less electricity 6-inch diameter x 1/2-inch thickness heating pad, cord length of 4-feet Made to UL 499, with GFCI for increased safety As always, includes our 2-year warranty

Same as the popular GQF poultry brooder, but without heating elements and thermostat. Has sliding clear plastic door panels on front and sides along with metal top panels and drop pan.

250 watt Infrared RED heat lamp light bulb & 250W Ceramic Base Brooder Lamp. High Quality, don't trust your birds to anything else, especially not a white bulb it can blind them. Features: Lasts 20 percent longer than standard heat lamp bulbs  uses standard 120 volt power  standard type A screw in power base (same as your household bulbs)  brass base to minimize corrosion and "freezing" in socket  Splatterproof hardened Pyrex glass designed not to shatter if contacted by liquids  average bulb life is 6000 hours NOTE: The bulb is for 110/120V AC Power - WE CANNOT SHIP THE BULB outside of the USA & Canada

For use in GQF No. 0427 Brooder. Fits through 1” hole. Length can adjust from 6” to 9”. To keep chicks healthy and prevent loss, set brooder temperature to 100°F and lower temperature 5°F each week to wean chicks off of needing supplemental heat.

The IncuKit XL™ for reptiles is an all-in-one kit designed to be the heart and brains of a homemade reptile incubator. It allows you to convert a cabinet-sized enclosure into an incubator! To make your own incubator, you can use anything from an old refrigerator to a custom built cabinet! Simply choose your enclosure and install your IncuKit XL™ for reptiles unit inside.  Pretty cool?  Well, actually it's pretty hot and it works very well.   The IncuKit XL™ for reptiles has been redesigned to work specifically in reptile incubators that require lower temps! The IncuKit XL™ for reptiles includes the following: Basic Thermostat module: This is a standard on/off thermostat.  This means that when the temperature hits a certain point, it turns the heater off and then back on full power once the temperature drops below a certain point.  It will control the heater and fan. This comes pre-set to 99.5 degrees F but is fully adjustable to the temperature required for reptile eggs.  1 x 125 Watt Heater/Fan: This heater/fan is great for providing heat to medium to large size reptile incubators. The included wire adapter makes it so the heater and fan turn off once the desired temperature is reached. This helps to minimize the drying out of eggs and overheating the incubator. To determine if the included heater/fan unit will provide enough heat, a simple light bulb test will help.  Get light bulbs that will generate enough heat to easily warm your incubator to at least your desired temperature. See how many watts are required and that will help you know which option to select. The buyer is responsible for determining if this will generate enough heat for your enclosure.    Caution: this is an AC powered device that you will be mounting in your incubator yourself.  You must use a great deal of common sense when dealing with electrical devices.  Electricity is wonderful but can be very dangerous.  Use caution, common sense and if in doubt, ASK AN EXPERT!!! The IncuKit includes the following: Electronic Basic Digital Thermostat 1 x Heater/fan. Each heater and fan module includes a high-output 120mm AC fan with protective screen, an integrated 125 watt heater with built-in safety thermal switch and mounting plate Adapter extension cord for reptile incubators All mounting hardware Installation and operating instructions Easy to install and set up.  All mounting hardware needed is included.  And our step-by-step video makes it easy to install.  Just mount the heater and fan module, mount the thermostat, connect them together and then plug it in.  It's so easy!!   Simple to install!  See this instructional video to see how simple it is to install this in your home-made incubator: If you find that your particular incubator needs more air circulation (a common issue in odd-shaped incubators), we offer 92mm and 120mm AC fans.     

Did you know that at any given time, the temperature in your Little Giant still air incubator can vary by up to five degrees from top to bottom and from the center to the corners? This occurs primarily because heat rises. Unfortunately, this temperature variation can have a significant negative impact on your hatch rates. This problem can be significantly reduced by installing a circulated air fan kit into your incubator. This fan circulates the air, which helps keep your whole incubator the same temperature. This can have a positive impact on hatch results. The more consistent air temperature also ensures that your thermostat is cycling on and off at the appropriate times, not just when the air around the thermostat heats or cools. Putting a fan inside your incubator is a great way to increase hatch rates, but it is not just as simple as buying a PC fan or a cheap fan kit. There are a few things that you need to keep in mind: Too much air circulation is bad for eggs, as it will dry them out. Think about it this way: there isn’t a fan blowing on eggs in nature. The only reason that an incubator needs the fan is to keep the temperature more consistent (like in nature). Beware of cheap kits, which often use high-speed fans. Almost all fans on the market are designed for cooling things, so they are made to move as much air as possible. This is not what you want. If your fan is too powerful it can overheat your incubator. Fans generate heat, and alternate fans are known to cook eggs. The direction the air flows and the positioning of the fan inside your incubator is critical to maintaining a consistent temperature throughout the incubator. Our fan kit includes simple instructions on how to do this. Miller Manufacturing has stopped producing the 7200 fan kit, but this kit can take its place. This item, along with the majority of our products, is covered by our Two Year IncuCare Warranty. Purchase today with no worries and experience the Little Giant Circulated Air Fan Kit for yourself. Video: Installation Video

Five Grow Off Pens make up the Battery. Includes base and swivel casters. When used in a battery, only one set of lids is supplied. The Grow Off and Holding pens are stacked and bolted together on a brooder base, which has ball bearing swivel casters for easy moving of the battery. (Same as Poultry Battery Brooder but without the expense of heating elements and thermostats.) Overall Dimensions: 38'' Wide, 42'' front to back, and 65'' high