Search results for "egg incubator":

Incubator Warehouse's Digital Electronic Egg Incubator Thermostat Description: This thermostat is very simple to use.  Just press the up arrow to set the temperature (in 0.1 degree increments).  There is a flame indicator on the screen that shows when the heater is operating.  The unit has an 18 inch remote sensor that is placed inside the incubator.  The white thermostat case is then mounted on the outside of the incubator.  Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Thermostat set point can be adjusted to any temperature between 41 - 113 degrees Fahrenheit Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) Select your voltage above in the drop down box (220/240V AC ONLY).  220/240V AC is for most places outside of North America. Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7.  NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should.  As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine!  This is true with any incubator and egg configuration.  Calibration Enabled.  This means that you can calibrate the thermostat to a specific temperature.  For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds). Product Instructions: IncuStat™ Basic

Plastic egg trays offer the most efficient system for gathering, spray disinfectant treating and storing of eggs. At time of setting eggs, just remove loaded egg tray from storage area and place it on the incubator turning rack. The No. 1500 and 1502 incubators are equipped with turning racks that will accomodate plastic trays to hold your eggs in place. Each No. 1502 turning rack will hold 2 pheasant egg trays (118 pheasant eggs) for a total of 354 eggs per incubator. (Not Stackable in GQF incubators). SET OF 6 TRAYS. COLOR MAY VARY.

25 Watt Heating Element for Hova-Bator Egg Incubator.  For replacement or can be used in DIY egg incubator. 110V AC Power. Clips not included see, available as an separate item.

The 1550 HATCHER incubator is designed to allow for the best hatching conditions. Unlike setting incubators, hatchers usually operate at slightly different temperature and humidity settings to obtain optimum hatch. With five hatching drawers the 1550 Hatcher will hold the complete setting of the 1500 incubator. For expanding operations the 1550 can be matched with up to three 1500 incubators. The 1550 can be used to set eggs, but each egg will have to be turned by hand. For small chicks such as quail, each hatching tray comes with a tray cover except for the bottom drawer. The No. 1550 HATCHER incubator offers an accurate digital thermostat with LCD display of Temperature and Humidity. An on-board computer monitors systems and the environment every second to keep itself updated and to share this data with you. Audio/visual indicators and a standard easy view door highlight a number of standard features. Constructed from high strength plastic board making it well insulated, quieter, and easier to clean. Each unit is hand assembled by our skilled craftsmen and tested for a full 24 hours for proper operation and calibration. Thermostat operating range between 60 and 103 degrees F. depending on room temperature. 110-120VAC, 50/60 Hz, 325 Watts TUV Listed Hatcher includes: 1 #3258 Digital Command Center 5 hatching trays 1 moisture pan with 2 wick pads Instruction booklet 4 hatching tray covers Total capacity approximately 1250 Quail eggs or 360 Chicken Eggs DIMENSIONS: 30 1/4” Front to Back, 15 3/4” Wide, 31 3/4” High. 

Perfect kit for anyone incubating reptiles. This kit has been designed to help all of our customers incubating reptile eggs get started. The HovaBator 2370 Incubator has a digital thermostat that is accurate and reliable with a bright and easy to read display. The Fan can be turned off which is a great feature for the incubation of reptile eggs. Includes Incubator Warehouse's 2 Year IncuCare Warranty.

This kit includes all the metal parts to assemble an entire cabinet turner assembly (3 Shelf) for a DIY incubator OR replacement for GQF cabinets (1500, 1502, or 1202E). TURNER MOTOR NOT INCLUDED (Sold Separately - SKU 3175 - Turner Motor Assembly). This turner fits egg racks 1243 (Quail), 1245 (Pheasant), 1246 (Chicken), 1248 (Goose/Turkey), & 1454 (Ostrich/Emu). Screws/ Bolts to attach to cabinet incubator walls NOT included, but all hardware to attach pieces together is included.

This fan is made with durable ball bearings for long life. Mounting holes on each corner make mounting in your incubator very easy. Just wire into your incubator so the fan is always on to keep your cabinet incubator temperature uniform. We also sell a 110V version. 220V AC, 80-105 CFM, 0.1 Amps, 22 Watts Purchase includes Two Year IncuCare Warranty.

Approx. 9 oz of Incubator Warehouses Reptile Egg Incubation Hatching Medium/Substrate and 4 350ml (approx. 12 fl oz) reptile medium bowls with ventilation holes and lids. Better Hatch Rates The IncubatorWarehouse.com's Reptile Hatching Medium is a bacteria/mold resistant soil that increases your hatch rates. Avoid the dangers of mold and bacteria growing in your hatching medium. A must-have for every reptile-hatching enthusiast or hobbyist. A low-cost alternative to HatchRite. Simple to use, instructions included Resists Mold/Bacteria Growth Low Cost, Better Hatch Rates!

This listing is for brand new battery connector set for the Genesis 1588 and the IncuKit Mini / IncuView. This connector allows you to power your incubator with a battery.NOTE: Please select the type of connector you need from the drop-down menu The alligator style clips will easily connect to the positive and negative terminals on your 12VDC battery The barrel connector ends plugs into the power wire of the Genesis 1588 or the power port of the IncuKit DC / IncuView This is great for a back-up power supply for those who may have frequent power outages A 12VDC battery can be your primary power source for those who are off the grid Would you like to see how this is used with the Genesis 1588 and IncuKit DC / IncuView? See this short video:

Did you know that at any given time, the temperature in your Little Giant still air incubator can vary by up to five degrees from top to bottom and from the center to the corners? This occurs primarily because heat rises. Unfortunately, this temperature variation can have a significant negative impact on your hatch rates. This problem can be significantly reduced by installing a circulated air fan kit into your incubator. This fan circulates the air, which helps keep your whole incubator the same temperature. This can have a positive impact on hatch results. The more consistent air temperature also ensures that your thermostat is cycling on and off at the appropriate times, not just when the air around the thermostat heats or cools. Putting a fan inside your incubator is a great way to increase hatch rates, but it is not just as simple as buying a PC fan or a cheap fan kit. There are a few things that you need to keep in mind: Too much air circulation is bad for eggs, as it will dry them out. Think about it this way: there isn’t a fan blowing on eggs in nature. The only reason that an incubator needs the fan is to keep the temperature more consistent (like in nature). Beware of cheap kits, which often use high-speed fans. Almost all fans on the market are designed for cooling things, so they are made to move as much air as possible. This is not what you want. If your fan is too powerful it can overheat your incubator. Fans generate heat, and alternate fans are known to cook eggs. The direction the air flows and the positioning of the fan inside your incubator is critical to maintaining a consistent temperature throughout the incubator. Our fan kit includes simple instructions on how to do this. Miller Manufacturing has stopped producing the 7200 fan kit, but this kit can take its place. This item, along with the majority of our products, is covered by our Two Year IncuCare Warranty. Purchase today with no worries and experience the Little Giant Circulated Air Fan Kit for yourself. Video: Installation Video

Did you know that at any given time, the temperature in your Hova-Bator still air incubator can vary by up to five degrees from top to bottom and from the center to the corners? This occurs primarily because heat rises. Unfortunately, this temperature variation can have a significant negative impact on your hatch rates. This problem can be significantly reduced by installing a circulated air fan kit into your incubator. This fan circulates the air, which helps keep your whole incubator the same temperature. This can have a positive impact on hatch results. The more consistent air temperature also ensures that your thermostat is cycling on and off at the appropriate times, not just when the air around the thermostat heats or cools. Putting a fan inside your incubator is a great way to increase hatch rates, but it is not just as simple as buying a PC fan or a cheap fan kit. There are a few things that you need to keep in mind: Too much air circulation is bad for eggs, as it will dry them out. Think about it this way: there isn’t a fan blowing on eggs in nature. The only reason that an incubator needs the fan is to keep the temperature more consistent (like in nature). Beware of cheap kits, which often use high-speed fans. Almost all fans on the market are designed for cooling things, so they are made to move as much air as possible. This is not what you want. If your fan is too powerful it can overheat your incubator. Fans generate heat, and alternate fans are known to cook eggs. The direction the air flows and the positioning of the fan inside your incubator is critical to maintaining a consistent temperature throughout the incubator. Our fan kit includes simple instructions on how to do this. This item, along with the majority of our products, is covered by our Two Year IncuCare Warranty. Purchase today with no worries and experience the Hova-Bator Circulated Air Fan Kit for yourself. Video: Installation Video