Search results for "IM Incubator":

  Incubator Warehouse's Digital Electronic Egg Incubator Thermostat for IncuKit XL Description: This thermostat is very simple to use. Just press the up arrow to set the temperature (in 0.1 degree increments). There is a flame indicator on the screen that shows when the heater is operating. The unit has an 18 inch remote sensor that is placed inside the incubator. The white thermostat case is then mounted on the outside of the incubator. Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) 110V AC Power Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7. NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should. As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. Calibration Enabled. This means that you can calibrate the thermostat to a specific temperature. For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds).  

Incubator Warehouse's Digital Electronic Egg Incubator Thermostat Description: This thermostat is very simple to use.  Just press the up arrow to set the temperature (in 0.1 degree increments).  There is a flame indicator on the screen that shows when the heater is operating.  The unit has an 18 inch remote sensor that is placed inside the incubator.  The white thermostat case is then mounted on the outside of the incubator.  Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Thermostat set point can be adjusted to any temperature between 41 - 113 degrees Fahrenheit Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) Select your voltage above in the drop down box (220/240V AC ONLY).  220/240V AC is for most places outside of North America. Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7.  NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should.  As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine!  This is true with any incubator and egg configuration.  Calibration Enabled.  This means that you can calibrate the thermostat to a specific temperature.  For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds). Product Instructions: IncuStat™ Basic

Imagine a chicken waterer that could save you money and allow you to go longer between feedings, making it easier for you to get things done, leave town or go on vacation. Believe it or not, the Noble Nest™ Bucket Nipple Waterer does all of this and more! They even clean the coop for you! – (Just Kidding, but don’t you wish?) Chickens need clean and fresh water to live and produce those amazing eggs we all love. The Noble Nest™ Bucket Nipple Waterer is effective at keeping water clean and fresh. In addition, the sealed nipple design prevents leaking. Durable Plastic construction means years and years of dependable use. Noble Nest™ Bucket Nipple Waterer is available in multiple configurations to easily allow installation in any coop, run, or free-range layout. Holds an impressive 5 gallons of water. Why are you still reading? Start saving money, and time by buying the Noble Nest™ Bucket Nipple Waterer now. And remember It’s backed by the Incubator Warehouse IncuCare 2 Year Warranty, so you’ve got nothing to lose. Are you really still reading this? Ok, we’ll throw in some free instructions.   Noble Nest™ Waterer Configurations 5 Nipple, Side Waterer Designed to sit on the side of coop or where one side of the waterer is not accessible to birds, though it could also be used in other locations as well. 8 Nipple, 360° Waterer Designed for 360° access for birds, best used in location where birds can access all sides of waterer.

This is a printed version of our 4 Part of our Intro to Hatching YouTube Series (see video links below) Illustrated Guide to Hatching Basic introduction to incubating eggs and brooding chicks Product has references to our products but is overall very educational and informational 28 Pages See Pictures for a sneak peak YouTube Video Series Intro to Hatching Part 1/4: Setup https://www.youtube.com/watch?v=MqnbL8qTvaI&t Intro to Hatching Part 2/4: Incubation Period https://www.youtube.com/watch?v=vq8NvC2mH0U&t Intro to Hatching Part 3/4: Hatching Period https://www.youtube.com/watch?v=e3JzvNvvRpU&t Intro to Hatching Part 4/4: After Hatch https://www.youtube.com/watch?v=L7gtp3QQWgY&t

The two biggest factors that affect hatch rate are temperature and humidity. With these factors in mind, we created the IncuTherm™ series of digital thermometer/hygrometers. The IncuTherm™ is able to accurately measure and display the temperature and relative humidity at the same time and can be set to either Fahrenheit or Celsius. Its compact design allows the IncuTherm™ to be placed inside the incubator without taking up much space, but the LCD screen is still easily readable. The built-in high and low memory feature stores the highest and lowest temperature and humidity readings since the last memory reset, which helps you ensure ideal conditions for a successful hatch. The IncuTherm™ has been factory calibrated to +/- 1°F (0.5°C) precision, which is twice as accurate as most standard digital thermometers available on the market. This accuracy level makes the IncuTherm™ series the easy choice when selecting a digital thermometer for your next hatch. This item, along with the majority of our products, is covered by our Two Year IncuCare Warranty. Purchase today with no worries and experience the IncuTherm™ Digital Thermometer/Hygrometer for yourself.

  The easy-to-use IncuView 3 Pro is durable, accurate and reliable. It has a whole line-up of features not available on any other incubator such as a 360° crystal clear hinged lid, AI incubator control module, and the EZ-View humidity system.   The accurate IncuView 3 Pro Control Module has proprietary AI technology (Artificial Intelligence) to automatically select the best settings for the proportional thermostat to achieve a successful hatch. The control module accurately displays both temperature (°F or °C) and humidity. Never miss a pip, zip or hatch with the built-in LED viewing lights and hatch timer with automatic egg turner shutoff 3 days before hatch. All of these features and more make the IncuView 3 Pro Control Module the best incubator to trust your eggs to.   Beyond the electronics the IncuView 3 Pro is packed with features to make every hatch a delight. The 360° hatch view is simply amazing. The durable plastic base is easy to clean and dishwasher safe. The EZ-View humidity system allows you to easily check and fill the water in the system. All of this makes having a successful hatch easier than ever.. Purchase the optional AquaTank and then just insert the AquaTank into the correct EZ-View port and forget about humidity management until the tank needs to be refilled.  The AccuMist takes humidity management to an all new level.  Simply set the desired humidity level in the settings and the IncuView 3 Pro will automatically manage your humidity.    Egg Capacity: 27 chicken*, 49 Quail*, or 17 Goose*   12V 5 Amp DC power (Allows 110V OR 220V Input)