Search results for "Digital hygrometer":

For use in GQF No. 0427 Brooder. Fits through 1” hole. Length can adjust from 6” to 9”. To keep chicks healthy and prevent loss, set brooder temperature to 100°F and lower temperature 5°F each week to wean chicks off of needing supplemental heat.

Incubator Warehouse's Digital Electronic Egg Incubator Thermostat Description: This thermostat is very simple to use.  Just press the up arrow to set the temperature (in 0.1 degree increments).  There is a flame indicator on the screen that shows when the heater is operating.  The unit has an 18 inch remote sensor that is placed inside the incubator.  The white thermostat case is then mounted on the outside of the incubator.  Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Thermostat set point can be adjusted to any temperature between 41 - 113 degrees Fahrenheit Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) Select your voltage above in the drop down box (220/240V AC ONLY).  220/240V AC is for most places outside of North America. Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7.  NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should.  As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine!  This is true with any incubator and egg configuration.  Calibration Enabled.  This means that you can calibrate the thermostat to a specific temperature.  For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds). Product Instructions: IncuStat™ Basic

This thermometer is included with all wafer thermostat Hova-Bator incubators produced after 2001 but may be used with any incubator. This lightweight thermometer is intended to be placed directly on top of the eggs so that it reads the temperature at egg level. Dimensions: 6.5'' X 3.5''

This innovative design conforms to the surface to better transfer heat to your bucket. This combined with the insulating pad ensures that the warmth get more effectivley to the water which allows this lower power heater to still be effective down to 0 degrees F. And it comes with a built-in thermostat so if it gets warm outside, it shuts the power off, saving you money! Keeps upto 6 gallons of water from freezing down to 0°F! Need less than 6 gallons? Try 65 watt designed for up to 3-gallons Provides better freeze protection with less electricity, Built in Thermostat so unit turns on at 37 degrees F to save energy! Made to UL 499, with GFCI for increased safety As always, includes our 2-year warranty

Product Features: Designed for Little Giant Incubators: Compatible with 9300, 10300, and 11300 models. Digital LCD Display: Easily check the current temperature and humidity levels. Precise Temperature Control: Ensures a stable environment for better hatch rates. Includes a Brand-New Sensor Set: Improves accuracy and reliability. User-Friendly Design: Simple button controls make adjustments quick and easy. Reliable Performance: Built to handle continuous incubation cycles. Product Description:  If your Little Giant 9300, 10300, or 11300 incubator isn't keeping a steady temperature or humidity, it might be time for a new thermostat controller and sensor. This replacement unit brings your incubator back to top performance, ensuring a stable environment for your eggs. With a digital LCD display, easy controls, and accurate temperature and humidity readings, this is the perfect fix for an incubator that's not working quite right. A working thermostat is the heart of your incubator. If it fails or starts giving inaccurate readings, your eggs could be at risk. This digital electronic thermostat is designed to provide precise temperature and humidity control, so you don't have to worry about fluctuations affecting your hatch rates. The easy-to-read LCD screen displays both current temperature and humidity, letting you monitor conditions at a glance. It also includes a new set of sensors to get the most accurate readings possible. Whether you're hatching chickens, ducks, quail, or reptiles, this controller helps create the perfect conditions for success. Replacing your Little Giant incubator thermostat controller is quick and simple; no special tools or technical skills are required. The included sensor set ensures your incubator is operating at peak accuracy. Simply connect the unit, adjust the settings to your desired incubation temperature, and monitor the real-time data on the LCD screen. The intuitive interface makes it easy to fine-tune conditions as needed. Maintaining a consistent environment is critical if you're serious about hatching eggs, whether they're from chickens, ducks, quail, or even reptiles. A faulty thermostat can ruin an entire hatch, but you can incubate confidently with this replacement controller and sensor. Don't let an outdated or malfunctioning controller affect your hatching success. Order this Little Giant digital thermostat controller and sensor combo today and keep your incubator working like new.

This is ONLY a rebuild kit for the Old Style AutoCoop Door Opener.  Purchase includes the white timer and the internal circuit board needed to completely rebuild your AutoCoop Door Opener Controller. Power supply not included.

Product Features: Real-Time Egg Temperature Readings: Mimics a real egg's thermal properties with a synthetic egg probe for accurate results. Long, Flexible 36" Cord: Allows convenient placement of the display while monitoring inside the incubator. Built-in Alarm: Alerts you to temperature changes, programmable in 1-degree increments for complete control. Memory Function: Tracks and stores high and low temperatures, so you're always informed about temperature fluctuations. Celsius or Fahrenheit Modes: Switch between units to suit your preference. Large LCD Display: Easy to read from a distance for hassle-free monitoring. Flip-Out Stand & Magnetic Mounting: Use the flip-out stand to place it on a flat surface or attach it to your incubator with the built-in magnets. Battery Included: Ready to use right out of the box with a 3V CR2032 battery. Two-Year IncuCare Warranty Product Description: When it comes to hatching eggs, nothing is more important than maintaining the correct temperature. The Egg-O-Meter™ egg incubator thermometer is here to make that easier than ever. Most thermometers measure the air temperature, which warms and cools faster than the egg temperature. Considering this, we have created the Egg-O-Meter™ thermometer to measure the internal temperature of your eggs, giving you more accurate readings and better results. If you're tired of guessing or worrying about temperature fluctuations in your incubator, the Egg-O-Meter™ is the solution you've been looking for. The thermometer comes with a synthetic egg probe that closely mimics the temperature of a real egg. It has a 36-inch cord, so you can place the large, easy-to-read LCD screen wherever it's most convenient while still monitoring the eggs inside the incubator. You can switch between Fahrenheit and Celsius and even set a programmable alarm to warn you if the temperature moves out of the ideal range (adjustable by just 1-degree increments). Plus, it stores the highest and lowest temperatures since the last reset so that you can keep track of fluctuations. Built for convenience, the Egg-O-Meter™ has a compact design with a flip-out stand and strong magnets on the back for easy placement. It includes a 3V CR2032 battery. So it's ready to use right out of the box. And with a 2-year IncuCare Warranty, you can feel confident in your purchase. How to Use the Egg-O-Meter™   Place the Synthetic Egg Probe: Position the probe directly in the incubator for accurate internal egg temperature readings. Set the Alarm: Program the alarm to notify you if temperatures exceed or drop below-desired levels. Monitor the Display: View real-time temperature readings using the large LCD screen. Analyze Trends: Use the high/low memory feature to identify temperature trends for improved hatch success. With the Egg-O-Meter™, you don't need to worry about fluctuating temperatures ruining your hatch. Its innovative features, durable design, and industry-leading accuracy make it the ultimate egg thermometer for your incubator. Order now and give your eggs the best chance to hatch with the Egg-O-Meter™.

AutoCoop™ Smart Door Controller