Search results for "design":

HovaBator Incubator (Model 2370) The thermostat is very accurate and reliable with a bright, easy to read display. Temperature reading can be changed from Fahrenheit to Celsius. Fan can be turned off for incubating reptile eggs. This incubator also includes two 4x6 inch windows on top for viewing, as well as high sidewalls to keep birds inside when the lid is removed. This incubator can hold approximately 46 chicken, 188 quail, 90 pheasant, and 40 turkey or duck eggs. This is a 110V version, purchase the voltage converter for 220/240V use. IncuTurn™ Automatic Egg Turner for HovaBator Egg Incubators Carefully engineered and tested the universal egg tray holds any size egg, saving you from purchasing expensive egg racks for different egg sizes. Eggs are gently rolled six times per day, similar to how they are turned in nature, preventing the yolk from settling and exercising the embryo. The universal egg tray can hold 42 Chicken, 70 Quail, or 28 Goose eggs. Installation is a breeze, simply slide the motor clip over the edge of the incubator and attach the turning tray and you’re ready to start incubating. This product is a direct replacement for all HovaBator Egg Turners. Guaranteed to outperform the HovaBator Egg Turners*. This is a 110V version, purchase the voltage converter for 220/240V use. *Guarantee covered by Incubator Warehouse's 2 Year IncuCare Warranty Quail Tray for IncuTurn™ (Optional Selection) The Quail egg tray holds quail and small bird eggs and increases egg capacity to 116 quail eggs verses the 70 quail eggs that the universal tray can hold. Incubator Warehouse Hatch Guidebook This illustrated 28-page book is the printed version of our 4 Part Intro to Hatching YouTube Series (see video links below). It gives a basic introduction to incubating eggs and brooding chicks. YouTube Video Series Intro to Hatching Part 1/4: Setup https://www.youtube.com/watch?v=MqnbL8qTvaI&t Intro to Hatching Part 2/4: Incubation Period https://www.youtube.com/watch?v=vq8NvC2mH0U&t Intro to Hatching Part 3/4: Hatching Period https://www.youtube.com/watch?v=e3JzvNvvRpU&t Intro to Hatching Part 4/4: After Hatch https://www.youtube.com/watch?v=L7gtp3QQWgY&t Incubator Warehouse EZ-Clean Chick Brush for Cleaning Incubator & Egg Cute Chick Brush for cleaning incubator or Eggs. 3 in x 4 in IncuBright™ Egg Candler One of the most exciting parts of incubating eggs is being able to watch the embryo progress during the various development stages. The IncuBright™ egg candler makes this joy possible by providing an easy and effective way to candle your eggs. It uses the latest in LED light technology, having one super bright CREE bulb the IncuBright™ illuminates your eggs for easy viewing, even with dark or large eggs. It has the only universal silicone rubber egg protector ring that lets you candle any size egg and is cordless making it easy use (batteries included). E-Z Water Filler The EZ Incubator Water Trough Filler makes the task of adding water accurately to any incubator a breeze. No more spilling water, overfilling, or guessing where your water will go. IncuTimer™ Egg Incubator Hatch Countdown Timer The IncuTimer™ was developed to make incubation of eggs easier. This simple and easy to use countdown timer helps you keep track of the time till your incubating eggs hatch. It has a maximum of 90-days and displays your remaining time till hatch in days, hours, and minutes. When the countdown reaches 0 the alarm will sound alerting you. For convenience we have added the hatch times for some of the most common and popular birds incubated these days. This makes it easier to know what to set your timer for when you place your eggs into the egg incubator. Instructions on how to operate are located on the back of each unit so you never have to worry about keeping up with an instruction sheet. Digital Hygrometer One of the biggest factors in achieving a successful hatch is correct humidity. With this factor in mind, we offer a digital hygrometer. The Digital Hygrometer can accurately measure and display the relative humidity. A compact design allows the Digital Hygrometer to be placed inside the incubator without taking up much space while a large LCD screen makes it easy to read. This helps you ensure ideal conditions for a successful hatch. Battery INCLUDED (LR44 Button Cell) Feeder & Waterer Kit The Incubator Warehouse feeder and waterer kit provides you with the essential supplies to feed and water your new birds after they hatch. Double-Tuf 1.5-quart poultry waterer Double-Tuf 1.5 lb. poultry feeder 1 - Pack of Waterer Stones- reflective color attracts birds 1 - Packet of poultry electrolyte 1 - Pack of high protein starter food - not included for shipments outside of US & Canada 1 - Set of feeding instructions for birds InstaBrooder™ with Vrooder™ Heater Plate Incubator Warehouse Insta Brooder™ Pen with a Removable Mesh Top 2 Disposable Brooder Liners for Easy Cleanup. The Vrooder™, The Brooder Heater Plate with a View (Accommodates up to 30 baby chicks) The InstaBrooder™ with Vrooder™ is an Incubator Warehouse exclusive. Pops open and sets up in an instant. Can hold up to 30 Chicks. Mesh roof zips closed to keep the chickens in and predators out. Easy cord access in the bottom corner allows the Vrooder™ cord to run out and Velcro’s shut to keep chicks in. Disposable Liners make clean up a breeze. InstaBrooder™ folds up to smaller than a purse for easy storage. Insta Brooder Pen Dimensions: 36 X 36 X 18 in. Vrooder™ Dimensions: 14.5" x 14.5" x 12.5". Power Spec: 110V AC, 40 Watts. NOT INTENDED FOR USE OUTDOORS (Garage/Barn are ok if temperatures do not drop below 25 degrees Fahrenheit). HumidiKit™-Auto Humidity System (Optional Selection) The answer to one of the common hassles with incubation is maintaining the humidity inside the incubator. No need to frequently fill the water reservoirs or struggle to maintain the desired humidity. This system is designed to instantly deliver accurate humidity to most incubators. The integrated digital hygrostat that measures and controls the humidity is fully adjustable so you can achieve the humidity range that is right for your eggs. The humidifier is designed to gently provide instant humidity and fresh air directly inside the incubator for an accurate humidity range. The humidifier also comes with a one-liter bottle which typically needs to be filled once a week for most desktop incubators. To extend the life of your HumidiKit we recommend using distilled water. This unit comes ready to install into your incubator; simply place the probes from the HumidiKit inside the incubator, insert the hose into a vent hole, fill the water bottle, and connect to power. Includes 2 Year IncuCare Warranty!

  Incubator Warehouse's Digital Electronic Egg Incubator Thermostat for IncuKit XL Description: This thermostat is very simple to use. Just press the up arrow to set the temperature (in 0.1 degree increments). There is a flame indicator on the screen that shows when the heater is operating. The unit has an 18 inch remote sensor that is placed inside the incubator. The white thermostat case is then mounted on the outside of the incubator. Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) 110V AC Power Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7. NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should. As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. Calibration Enabled. This means that you can calibrate the thermostat to a specific temperature. For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds).  

The IncuKit XL™ for reptiles is an all-in-one kit designed to be the heart and brains of a homemade reptile incubator. It allows you to convert a cabinet-sized enclosure into an incubator! To make your own incubator, you can use anything from an old refrigerator to a custom built cabinet! Simply choose your enclosure and install your IncuKit XL™ for reptiles unit inside.  Pretty cool?  Well, actually it's pretty hot and it works very well.   The IncuKit XL™ for reptiles has been redesigned to work specifically in reptile incubators that require lower temps! The IncuKit XL™ for reptiles includes the following: Basic Thermostat module: This is a standard on/off thermostat.  This means that when the temperature hits a certain point, it turns the heater off and then back on full power once the temperature drops below a certain point.  It will control the heater and fan. This comes pre-set to 99.5 degrees F but is fully adjustable to the temperature required for reptile eggs.  1 x 125 Watt Heater/Fan: This heater/fan is great for providing heat to medium to large size reptile incubators. The included wire adapter makes it so the heater and fan turn off once the desired temperature is reached. This helps to minimize the drying out of eggs and overheating the incubator. To determine if the included heater/fan unit will provide enough heat, a simple light bulb test will help.  Get light bulbs that will generate enough heat to easily warm your incubator to at least your desired temperature. See how many watts are required and that will help you know which option to select. The buyer is responsible for determining if this will generate enough heat for your enclosure.    Caution: this is an AC powered device that you will be mounting in your incubator yourself.  You must use a great deal of common sense when dealing with electrical devices.  Electricity is wonderful but can be very dangerous.  Use caution, common sense and if in doubt, ASK AN EXPERT!!! The IncuKit includes the following: Electronic Basic Digital Thermostat 1 x Heater/fan. Each heater and fan module includes a high-output 120mm AC fan with protective screen, an integrated 125 watt heater with built-in safety thermal switch and mounting plate Adapter extension cord for reptile incubators All mounting hardware Installation and operating instructions Easy to install and set up.  All mounting hardware needed is included.  And our step-by-step video makes it easy to install.  Just mount the heater and fan module, mount the thermostat, connect them together and then plug it in.  It's so easy!!   Simple to install!  See this instructional video to see how simple it is to install this in your home-made incubator: If you find that your particular incubator needs more air circulation (a common issue in odd-shaped incubators), we offer 92mm and 120mm AC fans.     

Incubator Warehouse's Digital Electronic Egg Incubator Thermostat Description: This thermostat is very simple to use.  Just press the up arrow to set the temperature (in 0.1 degree increments).  There is a flame indicator on the screen that shows when the heater is operating.  The unit has an 18 inch remote sensor that is placed inside the incubator.  The white thermostat case is then mounted on the outside of the incubator.  Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Thermostat set point can be adjusted to any temperature between 41 - 113 degrees Fahrenheit Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) Select your voltage above in the drop down box (220/240V AC ONLY).  220/240V AC is for most places outside of North America. Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7.  NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should.  As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine!  This is true with any incubator and egg configuration.  Calibration Enabled.  This means that you can calibrate the thermostat to a specific temperature.  For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds). Product Instructions: IncuStat™ Basic