Search results for "Heater":

Many people prefer to build their own incubators. This is a fun do-it-yourself project. We’ve found that the biggest difficulty people run into while developing their incubators is being able to find a reliable heat source and thermostat. We’ve solved this problem by creating the IncuKit™ series thermostat fan heaters. We have created the IncuKit™ MINI to turn any small container into an incubator. This provides the heat, air circulation and thermostat control you need to accurately control the environment in your container for hatching eggs. The IncuKit™ MINI comes with a proportional thermostat, built-in 40 watt heater, and a built-in fan. The proportional thermostat controls the amount of power that is supplied to the heater instead of simply turning the heater off and on. This provides more accurate temperature control than a standard off/on thermostat. The thermostat also comes preset to 99.5 degrees F which can be easily adjusted if necessary. The digital display makes it easy to read the current temperature and to make changes. The IncuKit™ MINI operates on low 12 Volt DC power and includes an AC-to-DC converter that works with both 110/120v and 220/240v power input. An optional DC turner motor can easily be added which is controlled by the control module and is fully adjustable. In case of power outages, the IncuKit™ MINI can also be powered with a 12V battery (additional battery connectors required). NOTE: You can optionally purchase the car power adapter or battery clips so you can keep your incubator running while on the road! This can be especially handy if you are transporting eggs or queen bee cells to their new location. As always, all of our products are covered by our 2 Year IncuCare Warranty. Purchase today with no worries and experience the IncuKit™ MINI for yourself. How to determine the appropriate size container for the IncuKit MINI: There are several factors that determine how much power will be required to heat your container up to the appropriate temperature to hatch eggs. The size of the container, how well it is insulated, the room temperature and how much the room temperature fluctuates will all have a significant impact. The best way to determine if the IncuKit™ MINI is the right size for your container is pretty simple. Just put a 40 watt light bulb in your container (ensure it is thermally insulated since they get pretty hot!) and measure how warm your container gets. If it easily gets to at least 100 degrees F, then the IncuKit™ MINI should work. It is the user’s responsibility to determine if this product will generate enough heat for your container.   See this video for an overview of the IncuKit MINI:

The New Incubator Warehouse Exclusive Insta Brooder Pen is here and answers all your needs for a durable bird brooder! Fully enclosable with a removable mesh top ensures as your birds grow you can keep the top closed to ensure they do not escape and stay safe in their pen. The mesh roof ensures you never lose sight of them and can see everything happening in the brooder pen. A Velcro section in one bottom corner allows the Vrooder™ Brooder Heater Plate power cord to run out of the pen and keeps your birds from getting out. The Vrooder™ simulates a mother hen keeping her chicks warm and cozy under her feathers. Keeping a constant temperature, using an integrated thermostat and heater the Vrooder can accommodate up to 30 chicks. As your chicks grow, simply raise the heat plate with the easy-to-adjust thumbscrews without needing to remove the heat plate from your brooder. Comes with 2 disposable liners made to fit inside the unit and is textured to provide firm footing for your newly hatched chicks. These disposable drop pan paper board liners catch all your bird dropping and allow you to remove when the floor gets too dirty and covered in droppings. Made from a durable material the Insta Brooder pen can be washed off in the yard to remove any remaining dropping residue after your birds have been moved to their coop/cage. Please allow proper amount of time for the pen to dry before packing up to avoid mildew and mold growth and damage to your Insta Brooder pen. Once dry simply collapse and fold up and slide into its storage bag until your next hatch. Insta Brooder Pen Dimensions: 36 X 36 X 18 in. Vrooder Dimensions: 14.5" x 14.5" x 12.5", Accommodates up to 30 baby chicks, Power Spec: 110V AC, 40 Watts. NOT INTENDED FOR USE OUTDOORS (Garage/Barn are ok if temperatures do not drop below 25 degrees Fahrenheit)

Fan Heater Combo Unit for the IncuKit™ XL. 125 Watt Heater and High Power Circulated Air Fan.  110V AC Power Click here to see the 220V International Version.

This listing is for brand new 225 watt replacement heater coil for cabinet style egg incubators. Wire heats and cools quickly, minimizing overheating, making this an ideal choice for larger egg incubators 225 watts of power Voltage requirement: 110/120VAC Click here to see the 220V International Version. This is a substitute for GQF Part # 3014 - 225 watt coil heater in cabinet style incubators

The IncuKit XL ™ is an all-in-one kit designed to be the heart and brains of a homemade cabinet incubator. It allows you to convert a cabinet-sized enclosure into an incubator! To make your own incubator, you can use anything from an old refrigerator to a custom built cabinet! Simply choose your enclosure and install your IncuKit XL™ unit inside. Pretty cool? Well, actually it's pretty hot and it works very well. The IncuKit XL™ series has been redesigned to provide you with more options and versatility! First, select which style of thermostat is best for you: Basic Thermostat module: This is a standard on/off thermostat. This means that when the temperature hits a certain point, it turns the heater off and then back on full power once the temperature drops below a certain point. It will control the heater. This comes pre-set to 99.5 degrees F. Advanced Thermostat module: This is a proportional thermostat. As the temperature gets closer to the target temperature, it begins tapering off the power to the heater. This provides more precise control and provides lower temperature variation in the incubator. This unit also has a count-down hatch timer and provides the option to control an egg turner motor, if you choose to use one. This comes pre-set to 99.5 degrees F Second, select how many heater and fan modules your container will require: The number of heater and fan modules will be determined by the size of your container, how well it is insulated and the temperature outside the incubator. The IncuKit XL™ can be configured with one or two heater and fan modules, depending on these factors. Each heater and fan module will provide 125 watts of power. For medium size containers this may be all you need. For larger containers, you can add a second module to add an additional 125 watts of power. Do determine which option is best for you, a simple light bulb test will help. Get light bulbs that will generate enough heat to easily warm your incubator to at least 100 degrees F. See how many watts are required and that will help you know which option to select. The buyer is responsible for determining if this will generate enough heat for your enclosure. Caution: this is an AC powered device that you will be mounting in your incubator yourself. You must use a great deal of common sense when dealing with electrical devices. Electricity is wonderful but can be very dangerous. Use caution, common sense and if in doubt, ASK AN EXPERT!!! The IncuKit includes the following: Electronic Pre-Set thermostat designed specifically for incubators by IncubatorWarehouse.com (see details below) Each heater and fan module includes a high-output 120mm AC fan with protective screen, an integrated 125 watt heater with built-in safety thermal switch and mounting plate All mounting hardware Installation and operating instructions Easy to install and set up. All mounting hardware needed is included. And our step-by-step video makes it easy to install. Just mount the heater and fan module, mount the thermostat, connect them together and then plug it in. It's so easy!!   Simple to install! See this instructional video to see how simple it is to install this in your home-made incubator: If you find that your particular incubator needs more air circulation (a common issue in odd-shaped incubators), we offer 92mm and 120mm AC fans.  

Replacement Fan/Heater Unit for GQF 2370 Tabletop Incubator.

Replacement heater and thermostat for GQF Box Brooders. 110 Volts

Brooder Heat Plates are wonderful but they can take some of the fun out of raising chicks by keeping them hidden and out of sight. We’ve put the enjoyment back into raising chicks with the introduction of the Vrooder™, The Brooder with a View. You won’t miss any of the action with the exclusive Vrooder™ viewing port. This port allows you not only to see and watch the cute birds but also to help keep them safe (birds can get stuck in the middle of a traditional brooder plate and suffocate). The Vrooder™ simulates a mother hen keeping her chicks warm and cozy under her feathers. Keeping a constant temperature, using an integrated thermostat and heater. Traditional heat lamps consume over 6 times as much electricity as the Vrooder™. With the electricity savings the Vrooder™ pays for itself in a matter of weeks. A traditional Red Bulb uses 250 Watts constantly vs only 40 watts intermittently (integrated thermostat turns heater on and off as needed) As your chicks grow, simply raise the heat plate with the easy-to-adjust thumbscrews without needing to remove the heat plate from your brooder. IP64 rating means it is built dust tight and water resistant. Cleanup is a breeze, simply wipe down with a wet rag without worrying about damaging the internal components. The Vrooder™ can safely accommodate up to 30 baby chicks. Power Specs: 110 volts and 40 watts. Heat Plate Dimensions: 14.5”L x 14.5”W x 1”H. Assembled Dimensions: 14.5”L x 14.5”W x 12.5”H.

Fan Heater Combo Unit for the IncuKit™ XL. 125 Watt Heater and High Power Circulated Air Fan.  220V AC Power Click here to see the 110V North America Version.

This listing is for brand new cartridge-style heaters. These heaters work well for heating cabinet incubators. They are each 3/8" diameter x 8" long (203mm). This listing is for the 220/240V 125 Watt version. We have another listing for a 110/120V version. The cartridge is made of Stainless Steel tubing. The electrical connection wires are a full 24" long with fiberglass insulation; the first 2 inches have an extra silicone sealing.

Replacement 2 Part frame clip for Vrooder frame.

220 Volt International Version. Click here to see the 110V North America Version. The IncuKit XL ™ is an all-in-one kit designed to be the heart and brains of a homemade cabinet incubator. It allows you to convert a cabinet-sized enclosure into an incubator! To make your own incubator, you can use anything from an old refrigerator to a custom-built cabinet! Simply choose your enclosure and install your IncuKit XL™ unit inside. Pretty cool? Well, actually it's pretty hot and it works very well. The IncuKit XL™ series has been redesigned to provide you with more options and versatility! IncuStat Basic Thermostat module: This is a standard on/off thermostat. This means that when the temperature hits a certain point, it turns the heater off and then back on full power once the temperature drops below a certain point. It will control the heater and fan. This comes pre-set to 99.5 degrees F. Select how many heater and fan modules your container will require: The number of heater and fan modules will be determined by the size of your container, how well it is insulated and the temperature outside the incubator. The IncuKit XL™ can be configured with one or two heater and fan modules, depending on these factors. Each heater and fan module will provide 125 watts of power. For medium size containers, this may be all you need. For larger containers, you can add a second module to add an additional 125 watts of power. To determine which option is best for you, a simple light bulb test will help. Get light bulbs that will generate enough heat to easily warm your incubator to at least 100 degrees F. See how many watts are required and that will help you know which option to select. The buyer is responsible for determining if this will generate enough heat for your enclosure. Caution: this is an AC-powered device that you will be mounting in your incubator yourself. You must use a great deal of common sense when dealing with electrical devices. Electricity is wonderful but can be very dangerous. Use caution, common sense and if in doubt, ASK AN EXPERT!!! The IncuKit includes the following: Electronic Pre-Set thermostat designed specifically for incubators by IncubatorWarehouse.com (see details below) Each heater and fan module includes a high-output 120mm AC fan with protective screen, an integrated 125-watt heater with built-in safety thermal switch and mounting plate All mounting hardware Installation and operating instructions Easy to install and set up. All mounting hardware needed is included. And our step-by-step video makes it easy to install. Just mount the heater and fan module, mount the thermostat, connect them together, and then plug it in. It's so easy!!   Simple to install! See this instructional video to see how simple it is to install this in your home-made incubator: If you find that your particular incubator needs more air circulation (a common issue in odd-shaped incubators), we offer 92mm and 120mm AC fans.  

The IncuKit XL Extension allows the user to extend their fans that are attached to either the IncuStat basic or advanced IncuStat. This cord provides further flexibility for mounting and placing of either IncuStats or the Fan Heater unit reducing hassle.

This innovative design conforms to the surface to better transfer heat to your bucket. This combined with the insulating pad ensures that the warmth get more effectivley to the water which allows this lower power heater to still be effective down to 0 degrees F. And it comes with a built-in thermostat so if it gets warm outside, it shuts the power off, saving you money! Keeps upto 6 gallons of water from freezing down to 0°F! Need less than 6 gallons? Try 65 watt designed for up to 3-gallons Provides better freeze protection with less electricity, Built in Thermostat so unit turns on at 37 degrees F to save energy! Made to UL 499, with GFCI for increased safety As always, includes our 2-year warranty

The IncuKit XL™ for reptiles is an all-in-one kit designed to be the heart and brains of a homemade reptile incubator. It allows you to convert a cabinet-sized enclosure into an incubator! To make your own incubator, you can use anything from an old refrigerator to a custom built cabinet! Simply choose your enclosure and install your IncuKit XL™ for reptiles unit inside.  Pretty cool?  Well, actually it's pretty hot and it works very well.   The IncuKit XL™ for reptiles has been redesigned to work specifically in reptile incubators that require lower temps! The IncuKit XL™ for reptiles includes the following: Basic Thermostat module: This is a standard on/off thermostat.  This means that when the temperature hits a certain point, it turns the heater off and then back on full power once the temperature drops below a certain point.  It will control the heater and fan. This comes pre-set to 99.5 degrees F but is fully adjustable to the temperature required for reptile eggs.  1 x 125 Watt Heater/Fan: This heater/fan is great for providing heat to medium to large size reptile incubators. The included wire adapter makes it so the heater and fan turn off once the desired temperature is reached. This helps to minimize the drying out of eggs and overheating the incubator. To determine if the included heater/fan unit will provide enough heat, a simple light bulb test will help.  Get light bulbs that will generate enough heat to easily warm your incubator to at least your desired temperature. See how many watts are required and that will help you know which option to select. The buyer is responsible for determining if this will generate enough heat for your enclosure.    Caution: this is an AC powered device that you will be mounting in your incubator yourself.  You must use a great deal of common sense when dealing with electrical devices.  Electricity is wonderful but can be very dangerous.  Use caution, common sense and if in doubt, ASK AN EXPERT!!! The IncuKit includes the following: Electronic Basic Digital Thermostat 1 x Heater/fan. Each heater and fan module includes a high-output 120mm AC fan with protective screen, an integrated 125 watt heater with built-in safety thermal switch and mounting plate Adapter extension cord for reptile incubators All mounting hardware Installation and operating instructions Easy to install and set up.  All mounting hardware needed is included.  And our step-by-step video makes it easy to install.  Just mount the heater and fan module, mount the thermostat, connect them together and then plug it in.  It's so easy!!   Simple to install!  See this instructional video to see how simple it is to install this in your home-made incubator: If you find that your particular incubator needs more air circulation (a common issue in odd-shaped incubators), we offer 92mm and 120mm AC fans.