IncuTherm Plus™ Hatch Monitor $26.99
The two biggest factors in achieving a successful hatch are correct temperature and humidity. With these factors in mind, we created the IncuTherm™ series digital thermometer/hygrometers. The IncuTherm Plus™ is able to accurately measure and display the temperature and relative humidity at the same time which can be displayed in both Fahrenheit or Celsius . The probe is placed inside the incubator. This allows the IncuTherm Plus™ to measure temperature and humidity on the inside of your incubator and display it on the outside. The built-in high and low memory stores the highest and lowest temperature and humidity readings since the last memory reset. This helps you ensure ideal conditions for a successful hatch. The IncuTherm Series has been factory calibrated to be accurate to within +/- 1°F (0.5°C) in the incubation temperature ranges. This is twice as accurate as most standard digital thermometers available on the market. This accuracy level makes the IncuTherm Series the easy choice when selecting a digital thermometer for your next hatch. As always, all of our products are covered by our One-year Hassle-free Guarantee. Purchase today with no worries and experience the IncuTherm Plus™ Hatch Monitor for yourself.
IncuTherm™ Temp/Humidity Gauge $15.99
The two biggest factors that affect hatch rate are temperature and humidity. With these factors in mind, we created the IncuTherm™ series of digital thermometer/hygrometers. The IncuTherm™ is able to accurately measure and display the temperature and relative humidity at the same time and can be set to either Fahrenheit or Celsius. Its compact design allows the IncuTherm™ to be placed inside the incubator without taking up much space, but the LCD screen is still easily readable. The built-in high and low memory feature stores the highest and lowest temperature and humidity readings since the last memory reset, which helps you ensure ideal conditions for a successful hatch. The IncuTherm™ has been factory calibrated to +/- 1°F (0.5°C) precision, which is twice as accurate as most standard digital thermometers available on the market. This accuracy level makes the IncuTherm™ series the easy choice when selecting a digital thermometer for your next hatch. This item, along with the majority of our products, is covered by our Two Year IncuCare Warranty. Purchase today with no worries and experience the IncuTherm™ Digital Thermometer/Hygrometer for yourself.
HumidiKit™ - Auto Humidity System for Incubators $146.99
One of the common hassles with incubation is maintaining the humidity inside the incubator. These hassles include the need to frequently fill the water reservoirs or not being able to maintain the desired humidity. We are proud to introduce the HumidiKit automatic humidity system for egg incubators. This system is designed to instantly deliver accurate humidity to most incubators. The integrated digital hygrostat that measures and controls the humidity is fully adjustable so you can achieve the humidity range that is right for your eggs. The humidifier is designed to gently provide instant humidity and fresh air directly inside the incubator for an accurate humidity range. The humidifier also comes with a one liter bottle which typically needs to be filled once a week for most desktop incubators. To extend the life of your humidiKit we recommend using distilled water. This unit comes ready to install into your incubator; simply place the probes from the HumidiKit inside the incubator, insert the hose into a vent hole, fill the water bottle, and connect to power. The HumidiKit is also covered by the IncubatorWarehouse Two-Year IncuCare Warranty so you can purchase with confidence.
Egg-O-Meter™ | Egg Incubator Hatching Thermometer - A Better Egg Thermometer! from $26.99
One of the biggest factors in achieving a successful hatch is maintaining the correct temperature. Most thermometers measure the air temperature, which warms and cools faster than the egg temperature. With that factor in mind, we have created the Egg-O-Meter thermometer which measures the actual egg temperature. The Egg-O-Meter has a sensor that is embedded in a synthetic egg which closely reflects the temperature of a real egg. Temperature can be displayed in either Fahrenheit or Celsius. A 36 inch cord allows for the large LCD screen to be placed in a convenient location, and still measure the temperature anywhere in the incubator. The built-in high and low memory stores the highest and lowest temperature since the last memory reset. In addition, a programmable alarm warns if the eggs reach an undesirable temperature (Set in 1 degree increments). This helps you ensure ideal temperatures for a successful hatch. As always, all of our products are covered by our 2 Year IncuCare Warranty. Purchase today with no worries and experience the Egg-O-Meter egg thermometer for yourself.
Digital Egg Scale - Accurate Humidity Measurement and Egg Sizing $20.99
Description One of the most accurate ways to determine if the humidity inside an incubator is correct is by the weight loss of an egg during incubation. During incubation as air passing through the shell of the egg causes some of the water to evaporate inside the egg making the egg lose weight. Jumbo size eggs typically sell for more than medium size eggs; this is why having the ability to accurately size your eggs can increase your profits. This IncubatorWarehouse.com’s EggScale has can accommodate any size egg from quail to goose while still having a compact design which makes it easy to store. The recessed egg tray keeps eggs from rolling while they are being weighed and the blue backlit LCD display makes it easy to read. Easy to follow instructions for measuring humidity by weight loss and egg sizing chart make using the scale a breeze. As always all or our products are covered by our One Year No-Hassle Guarantee so you can purchase with confidence. 
Incubator Warehouse Digital Hygrometer $15.99
This Hygrometer works great for measuring humidity in any incubator. The humidity gauge displays the humidity in the air as a percentage. This hygrometer is also a replacement for the hygrometer in the No. 1140 Incubator Warehouse IncuView Incubator Lid (Current model only - Does not replace the old dial hygrometer).
IncuStat™ Basic Digital Electronic Egg Incubator Thermostat from $52.99
  Incubator Warehouse's Digital Electronic Egg Incubator Thermostat Description: This thermostat is very simple to use.  Just press the up arrow to set the temperature (in 0.1 degree increments).  There is a flame indicator on the screen that shows when the heater is operating.  The unit has an 18 inch remote sensor that is placed inside the incubator.  The white thermostat case is then mounted on the outside of the incubator.  Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Thermostat set point can be adjusted to any temperature between 41 - 113 degrees Fahrenheit Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) Select your voltage above in the drop down box (110V AC OR 220/240V AC).  110V AC is for North America and a small number of other countries.  220/240V AC is for most places outside of North America. Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7.  NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should.  As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine!  This is true with any incubator and egg configuration.  Calibration Enabled.  This means that you can calibrate the thermostat to a specific temperature.  For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds). Product Instructions: IncuStat™ Basic
IncuTimer™ Egg Incubator Hatch Countdown Timer $15.99
The IncuTimer was developed to make incubation of eggs easier. This simple and easy to use countdown timer helps you keep track of the time till your incubating eggs hatch. The IncuTimer has a maximum of 90-days and displays your remaining time till hatch day in days, hours, and minutes. When the countdown reaches 0 the alarm will sound alerting you. For convenience we have added the hatch times for some of the most common and popular birds incubated these days. This makes it easier to know what to set your timer for when you place your eggs into the egg incubator. Instructions on how to operate the IncuTimer are located on the back of each unit so you never have to worry about keeping up with an instruction sheet.
Hova-Bator GQF Incubator Thermometer / Hygrometer (Wet Bulb) 3018 $38.99
In our opinion this thermometer should only be used by those that are familiar with Wet Bulb thermometers.  According to GQF This is the most accurate incubator thermometer available and has approximately a 4' stem which can be inserted in a 5/32' hole to permit reading of temperature from outside of incubator. The 2' dial permits easy and accurate reading of temperature and is graduated in one degree increments from 25 degrees to 125 degrees.  Wicks are attached and placed in the humidity pan to allow thermometer to read wet bulb temperatures. THIS THERMOMETER SHOULD BE USED IN CIRCULATED INCUBATORS ONLY.
IncuStat™ Basic for IncuKit XL $59.99
  Incubator Warehouse's Digital Electronic Egg Incubator Thermostat for IncuKit XL Description: This thermostat is very simple to use. Just press the up arrow to set the temperature (in 0.1 degree increments). There is a flame indicator on the screen that shows when the heater is operating. The unit has an 18 inch remote sensor that is placed inside the incubator. The white thermostat case is then mounted on the outside of the incubator. Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) 110V AC Power Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7. NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should. As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. Calibration Enabled. This means that you can calibrate the thermostat to a specific temperature. For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds).  
Sold out
Egg Incubation Countdown/up Timer $13.99
In incubation there is a saying that “nature doesn’t lie”, which means the best way to tell if your incubator is operating correctly is by the results of the hatch. For example, if your eggs hatch early the temperature was too warm or if they are late it was too cool. With the IncubatorWarehouse.com’s Poultry Timer (p-timer) keeping track of the incubation period is simple and easy.  Simply set the timer when you set the eggs to the appropriate number of days and the p-timer will keep track of the incubation time for you.  The p-timer counts down the days and hours during incubation and once the timer reaches zero the display will begin to flash and the timer will count up.  When the eggs hatch you will know exactly if they are on time, early, or late and you will be able to make adjustments for the next time you incubate. The p-timer has a space saving compact design with an easy to read LCD display. The adhesive backing makes the p-timer easy to mount anywhere so it doesn’t get lost. The p-timer is covered by the IncubatorWarehouse.com’s one year hassle-free guarantee so you can purchase with confidence.   
Sold out
Plug 'n Play Hygrostat for humidity control in Egg Incubator, Reptile Terrarium $62.99
The Plug ‘n Play Hygrostat is a digital electronic hygrostat with remote sensor designed specifically to control the humidity level in incubators and terrariums. It's great for both tabletop and cabinet incubators and large and small terrariums.  It comes pre-wired and ready to use. You can use watering device up to 500 Watts and you can use up to three devices. Simply plug in your pump, water valve, humidifier or any other watering device into the 3-outlet plug and you’re ready to go. The humidity set point can be adjusted in 1% increments. Setting it is very simple to do.  This unit comes with a 40 inch remote sensor that can be placed inside your incubator.  It also has a remote temperature sensor so it can compensate humidity measurements for changes in temperature.  Please note: this device does not display the temperature.   Set point can be adjusted to any humidity level between 1% - 99% Runs on 110V AC and will power 110V AC devices.  If you have a DC watering device, you'll need a power converter to change AC to DC (like a laptop power supply).   Calibration enabled. This means that you can calibrate the hygrostat, if required. For example, if you have a hygrometer that you trust and the digital hygrostat reads a little different, you can calibrate the hygrotstat to match the trusted hygrometer (calibrate in 1% increments up to +/- 10%) You are able to change the hysteresis from 1% - 30%.  This means you are able to set the range of humidity that turns the power on and off.  For example, if you set a hysteresis of 5, the hygrostat will wait until the humidity level has dropped 5% below your set point before turning on the power.  It will turn off the power as soon as the level hits the set point This device can also be set to control the power for a dehumidifying device as well, if desired (only one at a time, it can't do both at a time).   You will notice in the pictures that there are two different sensor probes.  The larger one senses the moisture level.  The smaller one measures temperature so that the humidity sensor can compensate for changes in temperature. As noted above, this unit does not display temperature.   What devices can I use with this device to get water into my container?   Great question!  There are three main options to consider. 1. Water valve - use a small water valve attached to a reservoir of water that is kept above your container.  When the valve is powered on, the valve opens and water flows into your chamber. The water can fill a water reservoir in your container of flow onto a wicking pad.  2. Small water pump - A mini pump will bring water from a container kept outside the container.  This is set up similar to the water valve but the water container does not have to be kept above your container.  3. Humidifier - you can get a mini unit that could fit insider your container or a larger one that would be kept outside the container and then use flexible pipe or hose to pump the moist air into your container.  With egg incubators, be sure to find one that have low enough air flow that it will not cool off the incubator too much.   Note: It is normal for the hygrostat to turn the watering device off and still have the humidity level increase a little bit. This happens because as the power to the watering device turns off, the water that has already entered the container still needs to warm up and stabilize. The same is true when the power turns back on: the humidity may decrease a little more as the water takes time to dissipate in your container.  The amount this happens will depend on how quickly your watering device puts water (or mist) into your container.   Keep in mind that the variation in humidity levels over a short period of time is not nearly as important as the average humidity level over several days.   As always, all of our products are covered by our One-year Hassle-free Guarantee. Purchase today with no worries and experience the Plug ‘n Hygrostat for yourself. Product Instructions: Plug N' Play Hygorstat
Sold out
Humidity Management Kit for Janoel 12 MagicFly Good Mother HBlife HatchMate – Complete Humidity Management Kit $15.99
Incubator Warehouse has solved the problem with managing humidity in this popular 9-12 egg incubator. With this complete humidity management kit you can finally have complete control over the humidity in your incubator. This kit includes the Incubator Warehouse Digital Hygrometer, EZ Water Filler, & Humidity Tray. With 3 different sized reservoirs it is simple to get your humidity level adjusted. Simply pour water in the main reservoir using the EZ water filler until it is full. If you need more humidity, just keep adding water until it spills over into the medium then large reservoirs through the integrated EZ overflow ports. The Digital Hygrometer makes it easy to see what your current humidity level is at in your incubator. Includes the 2 Year IncuCare Warranty
Sold out
Humidity Tray for Janoel 12 MagicFly Good Mother HBlife HatchMate – Easy Humidity Management $8.99
Incubator Warehouse has solved the problem with managing humidity in this popular 9-12 egg incubator. With this simple humidity tray insert you can finally have control over the humidity in your incubator. With 3 different sized reservoirs it is simple to get your humidity level adjusted. Simply pour water in the main reservoir until it is full. If you need more humidity, just keep adding and water and it will will spill over into the medium and then the large reservoir through the integrated EZ overflow ports. We also sell this water tray in a complete humidity management kit including the Incubator Warehouse Digital Hygrometer and EZ Water Filler (Not included in this listing, see other listing fore details).

Incubator temperature, measured by an incubator thermometer, is the most important element to having a successful hatch, followed by incubator humidity, which is measured by an incubator hygrometer.  Selecting the right incubator thermometer and incubator hygrometer is critical.  At IncubatorWarehouse.com we have narrowed the selection to the best digital incubator thermometer and incubator hygrometer options around.  We have tested our digital incubator thermometer and incubator hygrometer products in actual incubation environments to ensure that we supply high quality products.

A quality incubator thermometer and incubator hygrometer, which can be purchased as one combined unit called a digital incubator thermometer hygrometer, are critical to maintaining a consistent incubator temperature.  Maintaining 99.5 degrees Fahrenheit (37.5 degrees Celsius) incubator temperature will improve your hatch rates.  Our recommendation is to keep incubator humidity at 50-55% until the last 3 days of your hatch period and then raise the humidity to 65-70% for the last 3 days of the hatch.