IncuKit Parts

Product Features: Powerful Air Circulation: Spreads heat evenly inside the incubator. Durable Ball Bearings: Long-lasting performance with less maintenance. Easy Installation: Four corner-mounted holes make mounting simple and secure. Energy Efficient: Uses only 0.25 Amps and 22 Watts, reducing power consumption. Compact & Versatile: Ideal for cabinet incubators and other ventilation needs. Reliable Power: Runs on 110V AC with airflow of 80-105 CFM Includes 2-Year IncuCare Warranty. Product Description: Keeping the right temperature and humidity in your incubator is key for successful hatching. This 110V AC incubator fan for the cabinet egg incubator provides consistent airflow. It helps to move air evenly, keeping the temperature the same everywhere. This stops hot or cold spots that could harm egg development. This fan has high-quality ball bearings for long life and smooth use. Unlike sleeve-bearing fans, which wear out quickly, and can only be installed in one direction, ball-bearing fans last longer and need fewer replacements. This saves money, making it a smart choice for those who rely on their incubators for continuous hatching cycles. With its pre-drilled mounting holes in each corner, installing this egg incubator fan is easy. Whether you're adding a new fan or upgrading, you can attach it in a few quick steps. Just connect the wires to keep air circulating all the time. Technical Specifications Voltage: 110V AC Airflow: 80-105 CFM (Cubic Feet per Minute) Power Consumption: 22 Watts Current: 0.25 Amps Bearing Type: Ball Bearings Mounting: Four corner holes for secure installation   This axial fan is specifically made for cabinet egg incubators. It keeps the temperature steady for better hatching and spreads heat evenly, ensuring every egg gets the proper heat and ventilation. Need a 220V Version? No worries if you're outside the U.S. or need a different power setup. We also offer a 220V version. Check our store for more details. Don't let poor airflow ruin your hatch rates. Order now to give your eggs the best possible incubation environment.

  Incubator Warehouse's Digital Electronic Egg Incubator Thermostat for IncuKit XL Description: This thermostat is very simple to use. Just press the up arrow to set the temperature (in 0.1 degree increments). There is a flame indicator on the screen that shows when the heater is operating. The unit has an 18 inch remote sensor that is placed inside the incubator. The white thermostat case is then mounted on the outside of the incubator. Finally you can measure the temperature right next to your eggs, not the air at the top of the incubator. This can be set to read in Celsius or Fahrenheit Comes preset to 99.5 (this means that if you lose power the thermostat will come back on set to 99.5) - Preset to 37.5 in Celsius mode Digital readout displays temperature to the tenth of a degree (examples: 98.0, 99.5) If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc Designed specifically for incubators, great for small incubators AND cabinet incubators (can switch heating elements up to 225 Watts) Remote Temperature Sensor (18 inches long) 110V AC Power Temperature Switching Differential = 0.2 degrees Fahrenheit. This means if the thermostat is set to 99.5 the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7. NOTE: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the thermal mass of your heating element and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the egg to heat or cool more than it should. As long as the up and down cycle is relatively small, is less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. Calibration Enabled. This means that you can calibrate the thermostat to a specific temperature. For example: If you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Wiring and operation instructions included. It also includes instructions for installing an incubator fan, if desired. Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds).  

Genuine power supply for the IncuView and IncuKit Mini. 110V-240V AC power input 12V 5A DC output.