After-Hatch Supplies

Made by Miller Manufacturing of durable, easy-to-clean thermoplastic, this 20" has 28 individual holes to reduce wasted feed. The fliptop makes this feeder easy to refill, and rightly colored plastic helps attract birds to the food.

For use in all Box Brooders. Fits through 1 ⅛” hole. Measures from 50°F to 120°F.

The Plug ‘n Play is a digital electronic thermostat with remote sensor designed specifically for incubators. It's great for both tabletop and cabinet incubators. It comes pre-wired and ready to use. You can use any heating element up to 225 Watts. Simply plug in your heater, heat mat, or light bulb to the 3 outlet plug outlet and you’re ready to go. The temperature can be adjusted in 0.1 degree increments. Just press the up or down arrow to set it. The screen has a flame icon that turns on when the heater is operating. This unit comes with a 24 inch remote sensor that can be placed inside your incubator. The white thermostat may be mounted on the outside of the incubator. Comes preset to 99.5 degrees F (37.5 in Celsius mode). Set point can be adjusted to any temperature between 41-113 degrees F If the temperature goes over 99.9, it reads: 00.1, 00.2, 00.3, etc. The digital readout displays temperature to the tenth of a degree (98.7, 99.4) The temperature switching differential is 0.2 degrees F. This means that if the temperature is set to 99.5 then the thermostat will turn the heat on when the thermostat sensor reads below 99.3 and turn off when the sensor reads above 99.7 110V AC Calibration enabled. This means that you can calibrate the thermostat if required. For example, if you have a thermometer that you trust and the digital thermostat reads a little different, you can calibrate the thermostat to match the trusted thermometer (calibrate in 0.1 degree increments up to +/- 5 degrees) Key lock feature allows you to set the temperature and lock the keys so it cannot be changed without unlocking the keys (keys are locked by pressing both up and down buttons for 5 seconds) Note: It is normal for the thermostat to turn the heater off and still have the air temperature increase a little bit. This happens because as the power to the heater turns off, the heater is still hot and will heat the air around it. The same is true when the heater turns back on: the temperature may decrease a little more as the heater gets back up to temperature. The amount this happens will depend on the amount of heat your heating element holds and the amount of circulation in your incubator. Keep in mind that the air temperature may vary without a negative impact to the eggs if the variation is rapid enough to not allow the eggs to heat or cool more than it should. As long as the up and down cycle is relatively small, less than a few minutes, and the average air temperature is at your target temperature, the temperature inside your egg (which is what really matters) will be just fine! This is true with any incubator and egg configuration. As always, all of our products are covered by our 2 Year IncuCare Warranty. Purchase today with no worries and experience the Plug ‘n Play Digital Electronic Thermostat for yourself.

Keep chickens and game birds from roosting on their water bowls, preventing debris from getting into water. Fits ALL of the Little Giant Founts. Easily attaches to top of the fount with no extra hardware needed. Keep your birds' water fresh with the Little Giant Bowl Guard.

Base stand with swivel casters. Bolt to brooder. Brooders may be stacked & bolted together, up to five high. When stacking two or more brooders, use GQF #0572 Six Plug Electrical Outlet (not included). Base dimensions: 36'' x 32'' x 5''

Individual holes minimize waste. Top slides off for easy access and cleaning. Made of heavy gauge galvanized steel and feature rolled edges for safety.

Watering nipples are one of the best upgrades to a traditional chicken waterer. They're mess-free, so you'll spend far less time cleaning and scrubbing out poopy, dirty waterers, and more time enjoying your flock. Screw these nipples into the container of your choice (instructions provided), such as 5-gallon plastic buckets or a PVC pipe. What sets these apart from vertical nipples: they don't drip and, because no water is stored in the nipple unit even when your bucket or drinker is full of water, they won't freeze during the winter provided you're heating your water supply. Comes with the Incubator Warehouse 2 Year IncuCare Warranty. Installation requires a 3/8" drill bit. Don't have one? You can get yours HERE.

Watering nipples are one of the best upgrades to a traditional chicken waterer. They're mess-free, so you'll spend far less time cleaning and scrubbing out poopy, dirty waterers, and more time enjoying your flock. Screw these nipples into the container of your choice (instructions provided), such as 5-gallon plastic buckets or a PVC pipe. What sets these apart from vertical nipples: they don't drip and, because no water is stored in the nipple unit even when your bucket or drinker is full of water, they won't freeze during the winter provided you're heating your water supply. Comes with the Incubator Warehouse 2 Year IncuCare Warranty.